Series |
Model |
Description |
| VM-5 |
|
The VM-5 series supervisory vibration monitor
is designed in accordance with the American Petroleum
Institute Standard, API St'd 670, for use on rotating
machinery. Both a 10-slot rack mounting type and a single-unit
independent type with a built-in power supply are available. |
| VM-5 |
|
This is a highly reliable dual channel
vibration monitors which monitors the shaft vibration
of rotating machinery. Both a 10-slot rack mounting type
and a single-unit independent type with a built-in power
supply are available. |
| VM-5 |
|
This is a highly reliable dual channel
seismic vibration monitors which monitor the bearing vibration
of rotating machinery detected by a contact velocity vibration
transducer. Both a 10-slot rack mounting type and a single-unit
independent type with a built-in power are available. |
| VM-5 |
|
This is a highly reliable dual channel
bearing vibration monitor which monitors the bearing vibration
of rotating machinery detected by an acceleration transducer.
Both a 10-slot rack mounting type and a single-unit independent
type with a built-in powerare available. |
| VM-5 |
|
This is a highly reliable dual path vibration
monitor which monitors the velocity/ acceleration and
displacement/ velocity vibration of rotating machinery
simultaneously. The vibration monitors detect machine
failures early on and informs the operator of these failures. |
| VM-5 |
|
This is a highly reliable vibration monitor
which monitors the amount of shaft deflection (eccentricity
pk-pk) at machine start-up. Both a 10-slot rack mounting
type and a single-unit independent type with a built-in
power supply are available. |
| VM-5 |
|
This is a highly reliable dual channel
thrust monitor which monitors the shaft position of rotating
machinery. Both a 10-slot rack mounting type and a single-unit
independent type with a built-in power supply are available. |
| VM-5 |
|
This is a highly reliable Differential
Expansion Monitor which monitors the differential expansion
caused by thermal expansion of the rotor and casing rotating
machinery. |
| VM-5 |
|
This is a highly reliable ramp differential
expansion monitor which monitors the differential expansion
caused by thermal expansion of the rotor and casing of
rotating machinery. |
| VM-5 |
|
This is a highly reliable Differential
Expansion Monitor which monitors the differential expansion
caused by thermal expansion of the rotor and casing of
rotating machinery. |
| VM-5 |
|
This is a highly reliable case expansion
monitor which monitors the case expansion of rotating
machinery. Both a 10-slot rack mounting type and a single-unit
independent type with a built-in power supply are available.
|
| VM-5 |
|
This is a highly reliable valve position
monitor which monitors the valve opening. Both a 10-slot
rack mounting type and a single-unit independent type
with a built-in power supply are available. |
| VM-5 |
|
This is a highly reliable monitor which
monitors the rotor speed of the shaft and zero speed.
Both a 10-slot rack mounting type and a single-unit independent
type with a built-in power supply are available. |
| VM-5 |
|
This is a highly reliable Tachometer which
monitors the rotor speed of the shaft and rotor acceleration.
Both a 10-slot rack mounting type and a single-unit independent
type with a built-in power supply are available. |
| VM-5 |
|
The VM-5X1 interface Unit distributes and
outputs the recorder output from VM-5 Series vibration
monitor units and outputs analog signals distributed from
the VM-5X2,3 Interface Unit I/O module mounted on the
rear panel of theVM-5H3 or VM-5Wl Instrument Rack. |
| VM-5 |
|
The VM-5P Communication/Phase Marker Unit
accommodated in a VM-5H3 or VM-5W1 Instrument Rack processes
phase marker signals and also performs an external communication
function via the serial interface (RS-232C / RS-485). |
| VM-5 |
|
This unit supplies power to all VM-5 Series
Monitor Units acommodated in the same rack. A failt in
the power supply is indicated by lighting of the power
supply OK lamp and alarm contact output. |
| VM-5 |
|
This is a highly reliable Power Supply
Backup Model Unit, which backup the DC power supplied
to each VM-5 series units mounted in the VM-5H3 or VM-5W1
instrument rack, at the time of the instantaneous electric
power failure. |
| VM-5 |
|
The VM-5Y Relay Module Unit is designed
for use with VM-5 Series vibration monitors. Mounted on
the rear panel of the VM-5H3 or VM-5W1 lnstrument Rack,
this unit outputs contact signals such as input abnormaI,
alert and danger alarms for sequence control. |
| VM-5 |
|
The VM-5Y4,5,6 Relay Module Unit are available
for each VM-5 Series vibration monitors. These units are
the connector type Relay Module Unit mounted on the rear
panel of the VM-5H3 or VM-5W1 Instrument Rack. |
| VM-5 |
|
The VM-5G is a single-unit independent
type instrument rack with a power supply for each VM-5
series vibration monitor (except VM-5 Communication/Phase
Maker Unit) 4 points relay. SPDT (DAN. 1. DAN. 2, ALE.
1, ALE. 2) and OK relay. |
| VM-5 |
|
The VM-5H3 instrument rack which accommodates
the VM-5P communication/phase marker unit, VM-5 series
monitor, VM-5Y relay module unit and VM-5Z power supply
unit can be mounted on a panel or 19-inch standard rack.
|
| VM-5 |
|
The VM-5W1 dual power supply instrument
rack is designed to accommodates the VM-5Z power supply
unit.VM-5 series monitor and VM5-Y relay module unit for
mounting on a standard panel. This rack can accommodate
1 VM-5Pcommunication/phase marker unit. |
VM
Series |
|
This monitor is a highly
reliable Differential Expansion Monitor designed to measure
differential thermal expansion between the rotor and case
of rotating machinery. The monitor accepts the output
of the VM-5L Complementary Input Differential Expansion
Monitor and the case expansion signal from the LVDT, performs
compensation, and computers the differential expansion
value. |
VM Series |
|
This monitor which provides
detection of reverse revolutions, indicates of peak reverse
speed value if that have occurred. Both a 10-slot rack
mounting type and a single-unit independent type with
a built-in power supply are available. |
| |
|
This is a
highly reliable dual channel monitor which monitors the
temperature of rotating machinery. The monitor inputs
signal from grounded/nongrounded thermocouples, or 3-wire/4-wire
RTDs and displays them on LCD. |
| VM
Series |
|
This Unit is
designed for use with VM-5F Temperature Monitor. Mounted
on the rear panel of the VM-5H3 or VM-5W1 Instrument Rack,
this unit outputs contact signals such as ALERT and DANGER
alarms for sequence control. |
| VM
Series |
|
Monitors
the gap between the piston rod set as the target and the
sensing surface of the sensor for rod drop measurement
(VK / VC) so as to synchronize with the phase marker,
and then converts the gap thus measured to the amount
of rider ring abrasion. |
| |
|
Monitors the
gap between the piston set as the target and the sensing
surface of the sensor for rider ring abrasion measurement
(PK) to obtain the amount of abrasion. |
| VM-15 |
|
This new general-purpose
monitoring system provides all functions necessary for
monitoring vibration input from rotating machinery in
the form of displacement, velocity and acceleration signals,
and therefore allows any system design to suit a variety
of applications. The system offers ample power for monitoring
smaller scale rotating machinery. |
| VM-15 |
|
VM-15B1 ACCELERATION VIBRATION
MONITOR Used to prevent alarm output that is caused by
excessive vibration during machine startup. Block off
the DANGER/ALERT alarm, or switch the alarm setup value
to another number magnified by setup number. |
| VM-15 |
|
VM-15K1 DISPLACEMENT VIBRATION
MONITOR |
| VM-15
|
|
VM-15U1 VELOCITY VIBRATION
MONITOR |
| VM-16
|
|
The VM-16 is a 8 or 12-channel
vibration monitor to realize a high cost performance of
monitoring system for general-purpose machinery. It has
Danger, Alert and Not-OK relay contact outputs (OR logic
of each channel), digital display and alarm state lamps
for each channel. |
| VM-13V1
|
|
The Model VM-13V1 Vector Monitor
diagnoses the dynamic characteristics of rotating machinery
and offers highly accurate balancing data. It receives
rotating shaft phase reference (one pulse/revolution)
and multi-point vibration detector input signals. |
| MP Series |
|
This unit is a digital over speed signal
transmitter whose input is fed from the Model RD-05A Tacho
driver or MS series Magnetic pickup. |
| MP Series |
|
This unit is a digital zero speed signal
transmitter whose input is fed from the Model RD-05A Tacho
driver. |
| MP Series |
|
This unit is a thrust (shaft position)
abnormal signal transmitter whose input is fed from the
VK series transducer. |
| MP Series |
|
This unit is used to supply power to any
of the MP-1 series units (MP-1S, MP-1Z and MP-1T) mounted
in the MP-1W Instrument rack. Four types of AC and DC
power inputs are available, and any power input type to
meet the specification can be freely selected. |
| MP Series |
|
This rack can mount the MP-1P Power supply
units and any of the MP-1 series units (MP-1S, MP-1Z and
MP-1T), and then is mounted on panel as an assembly. One
MP-1W1 rack can mount up to 3 units and also one MP-1W2
rack can mount up to 6 units. |
